Repair Lawn Mower: Start Problems, Belt and Blade Fixes

Repair Lawn Mower: Start Problems, Belt and Blade Fixes

When you repair lawn mower trouble at home, you face one of three faults most of the time. The engine won’t start or dies, the self-propelled drive stops pulling, or the cut turns ragged. The most common lawn mower problem is an engine that won’t start, typically because of stale fuel. All three are home jobs with hand tools and the owner’s manual. Work the checks in order and stop at the first one that fixes it.

The money side is simple. A home repair costs the part. A shop charges for the same part plus labor.

You can repair the common lawn mower faults at home with basic hand tools. Check fuel, spark plug and air filter first when the engine won’t start. Replace a worn drive belt by following the model manual. Sharpen and balance the blade yourself. A DIY fix costs a part, while a shop adds labor.

Engine Won’t Start or Keeps Stalling

A mower that won’t start needs fuel, spark and air, checked in that order. Drain stale gas into an approved container and refill with fresh fuel. Take the old fuel to a hazardous waste drop-off, never down a drain. Pull the spark plug and replace it if it shows heavy carbon or a cracked insulator. Tap out or replace a clogged air filter.

Lawn mower
Lawn mower. Photo via Wikimedia Commons (Public domain)

An engine that starts and then stalls points to the carburetor or a blocked fuel cap vent. Spray carburetor cleaner into the bowl and jets. Then run the engine with the cap loosened. If it keeps running, the vent is blocked and the cap needs replacing. EPA evaporative emission standards for small engines cover fuel permeation and venting, so a replacement cap should match the original part for your model. Run every test outdoors, because exhaust contains carbon monoxide, a colorless, odorless, poisonous gas (CPSC). Take the mower to a shop when it still stalls after a carb cleaning or the engine knocks. For a closely related question, see our guide to can you mow wet grass.

How to Replace a Lawn Mower Drive Belt

Read the model manual before you touch the belt, because routing differs between self-propelled walk-behinds and riding mowers. Pull the spark plug boot and run the tank low. Remove the belt cover and the pulley guard. Photograph the belt route. Then slip the old belt off the engine pulley and the transmission pulley. Thread the new belt along the same path and refit the covers. Test the drive on flat ground before you mow.

Sharpen the Blade and Repair the Deck

A dull blade tears grass, and a sharp, balanced blade cuts it clean. Pull the spark plug boot first and wear heavy gloves. Block the blade with a piece of wood and loosen the bolt. File the cutting edge at its original angle. Hang the blade on a nail or a blade balancer. If one side drops, file metal off that side until it hangs level.

Viking lawn mower
Viking lawn mower. Photo: kallerna, CC BY-SA 3.0, via Wikimedia Commons

Scrape the deck while the blade is off. Look for cracks around the spindle and engine mounts and for rust holes along the edge. Wire brush surface rust and paint the bare metal. Refit the blade with the correct side up and tighten the bolt to the torque value in the manual.

As a rule of thumb, replace the mower when the deck is cracked under the engine mount or the engine itself has failed. Those two parts carry the whole machine.

Tools and Guides for DIY Mower Repair

A socket set, a torque wrench, a spark plug socket, a flat file, a blade balancer, carburetor cleaner and heavy gloves cover every job here. Keep the manual for your exact model. If it is lost, download it from the engine or mower maker by model number.

Problem First check DIY part Shop if
Won’t start Fresh fuel, spark plug Spark plug, air filter No spark with a new plug
Starts, then stalls Fuel cap vent, carburetor Carb cleaner, fuel cap Stalls after a carb cleaning
Drive won’t pull Belt wear and routing Drive belt Slips with a new belt
Ragged cut, vibration Blade edge and balance Blade or file Bent spindle or cracked deck

Wear ear protection for every test run. The NIDCD names lawn mowers as a home noise source, and long or repeated exposure at or above 85 dBA can cause hearing loss.

Related reading: Lawn Aerator.

Related reading: Push Mower Repair.

Related reading: how get rid of clover in lawn.

Frequently Asked Questions

Is it cheaper to repair or replace a lawn mower?

Repairing is cheaper for the faults above. A spark plug, air filter, belt or blade is a small part next to a new mower. As a rule of thumb, get a written shop quote and compare it with the price of a comparable new mower. If the quote comes close, replace.

Can I service my own lawn mower?

Yes. Spark plug, air filter, oil, blade and drive belt are all owner jobs with hand tools. Pull the spark plug boot before every job. Tilt the mower only to the side the manual names, so oil does not run into the carburetor or air filter.

Sources




One Comment

Comments are closed.